asMODus gives the Spruzza a re vamp with the new Mosaic Edition Spruzza Kit! The Mosaic Edition replaces the fully stabilized wood doors with newly designed acrylic doors which have small chips of multi colored stabilized wood embedded into the doors to create a truly unique, "Mosaic" look.
The Spruzza is a compact, high end squonk ready mod with removable doors. The Spruzza utilizes the all new SSS (Smart Siphon System) which is sure to revolutionize the squonking style platform. The SSS system utilizes a pump located on the body of the mod that siphons juice through the 510 pin and pumps juice into any squonk ready atomizer. The impressive internal reservoir of the SSS holds an impressive 6.0mL of juice. Cleaning of the SSS was made to be exceptionally simple with no disassembly required. By pumping VG though the SSS it will flush the system. Each Spruzza comes pre primed with VG to ensure smooth operation right out of the box.
The Spruzza is powered by a GX-80-HUT chip which allows control of firing modes (Power, Curve, TC, TFR, and TCR) with full touch screen power. The Mosaic Edition Spruzza's body features acrylic, stabilized wood sprinkled battery doors. One door opens to allow access to the SSS for filling or checking your juice reserves and the other door opens to allow for access to your battery. The SSS and the battery ports have been intentionally put on opposite sides of the mod so that just in case the SSS is overfilled and spills, it will not be able to leak into the internals of the mod.
Partnered with the Mosaic Spruzza is the all new Oni-One RDA. The Oni-One is a single coil RDA which uses two large posts situated an opposite sides of the building deck. Each post offers two terminal slots and were constructed to easily accommodate just about any wire you through its way. The hex screws are fully removed, the wire is then laid through the post's hole which easily catches and sets the wire in place and is then secured by screwing the screw back into place over the wire. The improved building experience does not end there. On the exterior of the building deck are two rivets on opposite sides which reside in between both posts which allow the user to easily adjust the coil into the perfect position. By using the rivets as a guide you can use a screwdriver or coiler to provide perfect alignment of the coil.
Airflow on the Oni-1 RDA takes form as angled, side inlets which provide direct-to-coil side intake in bottom airflow fashion due to the upwards angles of the inlets. This direct bottom airflow provides unparalleled flavor. The One-One RDA comes preinstalled with a bottom feeding pin so you can start squonking right out of the box. The Oni-One offers a unique bottom feeding system that utilizes a split squonk pin which was crafted to evenly distribute any bottom fed juice throughout the deep juice well.
The Oni-One RDA utilizes a conical top cap topped with a conical 810 Delrin drip tip which helps condense the flavor of the vapor produced while providing svelte aesthetics. On the inside of the top cap, located towards the top of the cap around the drip tip port, is a ridged Delrin ring which acts as both a heat sink which drastically reduces transfer of heat to your mouth as well as preventing spitback during use. This internal cap design allows for any juice that travels upwards during use to get caught and slowly drip back into the well.
Product Specifications (Spruzza):
- Powered by the GX-80-HUT
- Requires 1x 18650 sized battery (not included)
- Touch screen type: Capacitive (requires the electrical properties of the human bodt to detect when and where the display is touched)
- Uses both touch and swipe technology
- Minimum atomizer resistance: 0.1 ohm
- Output wattage range (power mode): 5.0 - 80.0 watts
- Output wattage range (TC modes): 5.0 - 60.0 watts
- Temperature control supports the types: Ni200 Nickel, Ti Titanium, SS317, SS316, and SS304
- Temperature control range: 212°F - 572°F / 100°C - 300°C
- Powered by the all new SSS (Smart Siphon System) which allows for a more evolved squonking system as opposed to the traditional bottle squonking method
- Protections: Reverse polarity, short-circuit, overcharge, and low voltage
- Upgradeable firmware
Product Specifications (Oni-One RDA):
- Diameter: 24mm
- Two post styled building deck which both maximizes building space as well as creating the perfect way for juice to come through the base of the RDA
- Split bottom feeding pin which evenly distributes juice through two holes located on opposite sides
- Flavor enhancing conical top cap and drip tip to maximize flavor
- Airflow presents as side airflow inlets which are upwards angled to provide a bottom airflow-esque experience without bottom airflow inlet leaking
- Conical top cap with a heat sink located at the top of the RDA which drastically reduces any transfer of heat your mouth and catches any juice that travels up the cap of the RDA during use and allows it to fall back into the well
- 1x Spruzza 80W Mod by asMODus
- 1x Oni-One Squonk RDA
- 1x Spare part pack
- 2x Pre wrapped Fused Clapton coils
- 1x User manual
- 1x Warranty card
NOTE: The SSS (Smart Siphon System) was not intended to be taken apart for cleaning. DO NOT attempt to take the SSS apart. Once the SSS has been disassembled, the vacuum seal is lost and can not be repaired.